Custom Glass

Frameless Shower Glass in Metro Detroit

Nothing finishes a tiled bath like a clean panel of frameless glass with no aluminum to interrupt the line. We match you with our network glass specialist, who templates to your finished tile and hangs every enclosure plumb.

Typical range: $900–$3500 per project

Licensed & insured local pros
Permit-ready for custom glass work
Free, no-obligation quotes

Get a Free Quote Call Now

Free Quote — 60 Seconds

Tell us about your project and we’ll match you with a vetted, licensed local pro. No obligation.

A frameless shower enclosure is held up entirely by precision: heavy tempered glass, hinges anchored into blocking, and a template cut to the tile you actually installed rather than the rough opening a builder framed months earlier. A sixteenth of an inch off and the door drags, the gaps gape, or water tracks onto the floor. This is glamour work that lives or dies on measurement, which is exactly why the custom-glass piece of a Metro Detroit renovation runs through a dedicated glass specialist in our network rather than a general handyman with a level.

The glass specialist fabricates and installs frameless, semi-frameless, and framed enclosures, steam-shower glass to the ceiling, and the notched panels that wrap a bench or a knee wall. They scribe to out-of-square walls, set the hardware finish to match your fixtures, and seal the wet edges so the only thing you notice is how much bigger the bathroom suddenly feels.

What’s included

On-site template taken from your finished, grouted tile
Tempered safety glass cut and edge-polished to spec
3/8" or 1/2" thickness selected for the door and panel layout
Hinges, clamps, and handle in your chosen hardware finish
Wall scribing for out-of-plumb tile and corners
Protective anti-spot coating applied at the factory (optional)
Wet-edge sealing and a leak-checked final walk-through

Frameless glass is heavy, sharp, and unforgiving of a bad measurement — a botched template is a wasted slab, not a quick fix. Our specialist templates to the tile, anchors into real blocking, and carries the insurance this kind of overhead glass work demands.

How it works

Template the opening

A glazier measures the finished tile, checks every wall for plumb, and records the swing and hardware so the cut list matches reality, not the framing.

Fabricate the glass

Tempered panels are cut, the exposed edges are polished, holes and notches are bored, and any anti-spot coating is baked on before the glass leaves the shop.

Set the hardware

Hinges and clamps are anchored into the blocking behind the tile, located precisely so the door carries its weight without sagging or springing back.

Hang & align the glass

The fixed panel and door are lifted in, shimmed plumb, and adjusted until the reveals are even and the door holds at any angle.

Seal & demonstrate

Wet edges are sealed, the swing is tested, and you are shown how the door is meant to operate and be cleaned before the crew leaves.

Frameless Shower Glass guides

Everything you need to plan your project with confidence.

Frameless Shower Glass by city

We match shower glass projects with vetted pros across Metro Detroit.

Frameless Shower Glass: common questions

How long after my tile is finished can the glass go in?

The template can only be taken once the tile is set, grouted, and the corners are caulked — measuring sooner risks a panel that does not fit. From template to install is typically one to three weeks while the glass is fabricated and the coating is applied. Plan the glass as the final step of the bathroom, not a same-day add-on.

Will a frameless door leak onto my floor?

A correctly designed enclosure manages water rather than sealing it like a submarine. The glazier sets the proper slope, positions the door so spray stays inside, and seals the wet edges and bottom sweep. Leaks almost always trace back to a sloppy template or a door hung out of plumb, which is the whole reason measurement is treated so seriously.

Is 1/2" glass worth it over 3/8"?

For a tall single panel or a wide door, the extra thickness feels noticeably more solid and resists flex, and many homeowners prefer the heft. For a standard door-and-panel layout, 3/8" is the workhorse and looks identical from across the room. The glazier recommends the thickness based on the span and the door size, not on upselling.

Can you match the hardware to my faucet finish?

Yes. Hinges, clamps, the handle, and the header bar all come in finishes like chrome, brushed nickel, matte black, and brushed gold, and the specialist matches them to your fixtures so the room reads as one intentional package rather than a mix of metals.

Get matched with a shower glass pro

Get matched with a vetted, licensed Metro Detroit pro today. Free quotes, no obligation.